a9071d02b5
The Linksys MR8300 is based on QCA4019 and QCA9888 and provides three, independent radios. NAND provides two, alternate kernel/firmware images with fail-over provided by the OEM U-Boot. Hardware Highlights: SoC: IPQ4019 at 717 MHz (4 CPUs) RAM: 512MB RAM SoC: Qualcomm IPQ4019 at 717 MHz (4 CPUs) RAM: 512M DDR3 FLASH: 256 MB NAND (Winbond W29N02GV, 8-bit parallel) ETH: Qualcomm QCA8075 (4x GigE LAN, 1x GigE Internet Ethernet Jacks) BTN: Reset and WPS USB: USB3.0, single port on rear with LED SERIAL: Serial pads internal (unpopulated) LED: Four status lights on top + USB LED WIFI1: 2x2:2 QCA4019 2.4 GHz radio on ch. 1-14 WIFI2: 2x2:2 QCA4019 5 GHz radio on ch. 36-64 WIFI3: 2x2:2 QCA9888 5 GHz radio on ch. 100-165 Support is based on the already supported EA8300. Key differences: EA8300 has 256MB RAM where MR8300 has 512MB RAM. MR8300 has a revised top panel LED setup. Installation: "Factory" images may be installed directly through the OEM GUI using URL: https://ip-of-router/fwupdate.html (Typically 192.168.1.1) Signed-off-by: Hans Geiblinger <cybrnook2002@yahoo.com> [copied Hardware-highlights from EA8300. Fixed alphabetical order. fixed commit subject, removed bogus unit-address of keys, fixed author (used Signed-off-By to From:) ] Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
98 lines
1.8 KiB
Plaintext
98 lines
1.8 KiB
Plaintext
// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
|
|
|
|
/dts-v1/;
|
|
|
|
#include "qcom-ipq4019-xx8300.dtsi"
|
|
|
|
/ {
|
|
model = "Linksys EA8300 (Dallas)";
|
|
compatible = "linksys,ea8300", "qcom,ipq4019";
|
|
|
|
|
|
aliases {
|
|
led-boot = &led_wps_amber;
|
|
led-failsafe = &led_wps;
|
|
led-running = &led_linksys;
|
|
led-upgrade = &led_world;
|
|
serial0 = &blsp1_uart1;
|
|
};
|
|
|
|
|
|
leds {
|
|
compatible = "gpio-leds";
|
|
|
|
// Retain node names from running OEM on EA8300
|
|
|
|
// Front panel LEDs, top to bottom
|
|
|
|
led_plug: diag {
|
|
label = "ea8300:amber:plug";
|
|
gpios = <&tlmm 47 GPIO_ACTIVE_HIGH>;
|
|
};
|
|
|
|
led_world: internet {
|
|
label = "ea8300:amber:world";
|
|
gpios = <&tlmm 49 GPIO_ACTIVE_HIGH>;
|
|
};
|
|
|
|
led_wps: wps {
|
|
label = "ea8300:white:wps";
|
|
gpios = <&tlmm 46 GPIO_ACTIVE_HIGH>;
|
|
};
|
|
|
|
led_wps_amber: wps_amber {
|
|
label = "ea8300:amber:wps";
|
|
gpios = <&tlmm 22 GPIO_ACTIVE_HIGH>;
|
|
panic-indicator;
|
|
};
|
|
|
|
led_linksys: pwr {
|
|
label = "ea8300:white:linksys";
|
|
gpios = <&tlmm 45 GPIO_ACTIVE_HIGH>;
|
|
};
|
|
|
|
// On back panel, above USB socket
|
|
|
|
led_usb: usb {
|
|
label = "ea8300:green:usb";
|
|
gpios = <&tlmm 61 GPIO_ACTIVE_LOW>;
|
|
trigger-sources = <&usb3_port1>, <&usb3_port2>,
|
|
<&usb2_port1>;
|
|
linux,default-trigger = "usbport";
|
|
};
|
|
};
|
|
|
|
keys {
|
|
compatible = "gpio-keys";
|
|
|
|
reset {
|
|
label = "reset";
|
|
linux,code = <KEY_RESTART>;
|
|
gpios = <&tlmm 50 GPIO_ACTIVE_LOW>;
|
|
};
|
|
|
|
wps {
|
|
label = "wps";
|
|
linux,code = <KEY_WPS_BUTTON>;
|
|
gpios = <&tlmm 18 GPIO_ACTIVE_LOW>;
|
|
};
|
|
};
|
|
};
|
|
|
|
&wifi0 {
|
|
status = "okay";
|
|
qcom,ath10k-calibration-variant = "linksys-ea8300-fcc";
|
|
};
|
|
|
|
&wifi1 {
|
|
status = "okay";
|
|
ieee80211-freq-limit = <5170000 5330000>;
|
|
qcom,ath10k-calibration-variant = "linksys-ea8300-fcc";
|
|
};
|
|
|
|
&wifi2 {
|
|
status = "okay";
|
|
ieee80211-freq-limit = <5490000 5835000>;
|
|
qcom,ath10k-calibration-variant = "linksys-ea8300-fcc";
|
|
};
|