40966d612e
The Actiontec R1000H is a gigabit wifi router, 2.4 GHz single band with
two external antennas. It comes with a coaxial HomePNA port.
Hardware:
- SoC: Broadcom BCM6368
- CPU: dual core BMIPS4350 V3.1 @400Mhz
- RAM: 64 MB DDR
- Flash: 32 MB parallel NOR
- LAN switch: Broadcom BCM53115, 5x 1Gbit
- LAN coaxial : 1x HPNA 3.1, CG3211 + CG3213
- Wifi 2.4 GHz: Broadcom BCM4322 802.11bgn
- USB: 1x 2.0
- Buttons: 2x, 1 reset
- LEDs: 7x
- UART: yes
The HPNA hardware probably needs a firmware to make the coaxial port work.
In the OEM firmware, it's apparently sent with an utility (inhpna) through
the ethernet port.
Installation via CFE web UI:
1. Connect the UART serial port.
2. Power on the router and press enter at the console prompt to stop the
bootloader.
4. Browse to http://192.168.1.1 and upload the OpenWrt CFE firmware
5. Wait a few minutes for it to finish
Signed-off-by: Daniel González Cabanelas <dgcbueu@gmail.com>
(cherry picked from commit e1a55de7a7eafd40a4fab5f29153a1a3c3606818)
39 lines
1.2 KiB
Plaintext
39 lines
1.2 KiB
Plaintext
# SPDX-License-Identifier: GPL-2.0-or-later
|
|
|
|
. /lib/functions/leds.sh
|
|
. /lib/functions/uci-defaults.sh
|
|
|
|
board_config_update
|
|
|
|
case "$(board_name)" in
|
|
actiontec,r1000h)
|
|
ucidef_set_led_usbport "usb" "USB" "green:usb" "usb1-port1" "usb2-port1"
|
|
ucidef_set_led_netdev "wan" "WAN" "green:wan" "wan"
|
|
;;
|
|
comtrend,wap-5813n)
|
|
ucidef_set_led_usbport "usb" "USB" "green:usb" "usb1-port1" "usb2-port1"
|
|
;;
|
|
netgear,dgnd3700-v1 |\
|
|
netgear,dgnd3800b)
|
|
ucidef_set_led_netdev "lan" "LAN" "green:lan" "switch.1"
|
|
ucidef_set_led_netdev "wan" "WAN" "green:wan" "wan"
|
|
ucidef_set_led_netdev "wlan0" "WIFI2G" "green:wifi2g" "phy0-ap0"
|
|
ucidef_set_led_netdev "wlan1" "WIFI5G" "blue:wifi5g" "phy1-ap0"
|
|
ucidef_set_led_usbport "usb1" "USB1" "green:usb1" "usb1-port1" "usb2-port1"
|
|
ucidef_set_led_usbport "usb2" "USB2" "green:usb2" "usb1-port2" "usb2-port2"
|
|
;;
|
|
netgear,evg2000)
|
|
ucidef_set_led_netdev "lan" "LAN" "green:lan" "switch.1"
|
|
ucidef_set_led_netdev "wan" "WAN" "green:wan" "wan"
|
|
ucidef_set_led_usbdev "usb" "USB" "green:usb" "usb1-port1" "usb2-port1" "usb1-port2" "usb2-port2"
|
|
;;
|
|
observa,vh4032n)
|
|
ucidef_set_led_usbport "usb1" "USB1" "blue:hspa" "usb1-port1" "usb2-port1"
|
|
ucidef_set_led_usbport "usb2" "USB2" "red:hspa" "1-2-port1" "1-2-port2"
|
|
;;
|
|
esac
|
|
|
|
board_config_flush
|
|
|
|
exit 0
|