Fix issue with LAN1 interface on ap3935 devices, where the LAN
1interface won't come up after boot unless the bootloader has
initialized the network stack. Use of `fixed-link` in the prior code
kept the driver from clobbering PHY settings, but now that the driver
supports rgmii-id phy-mode, we can just use that.
Signed-off-by: Bryan Berg <bdb@north-eastham.org>
Link: https://github.com/openwrt/openwrt/pull/13629
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Updates ap3935 target to use the mdio controller built-in to gmac0,
rather than having the SoC bit-bang mdio from gpio pins
Signed-off-by: Bryan Berg <bdb@north-eastham.org>
Link: https://github.com/openwrt/openwrt/pull/13629
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Fix broken line break for Linksys e8350-v1 pushed with CRLF instead of
LF.
Fixes: 45b3c620e597 ("ipq806x: add support for Linksys e8350-v1")
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
AC2400 Dual-Band Gigabit Wi-Fi Router base on ipq8064.
https://www.linksys.com/support-product?sku=E8350
Specification:
- Qualcomm dual-core IPQ8064 @ 1.4 GHz
- 512 MB of RAM
- 4 MB of SPI NOR MX25U3235F
- 128 MB of NAND S34MS01G2
- Qualcomm QCA9880 2.4GHz 802.11bgn
- Quantenna QSR1000 5GHz 802.11ac (no support)
- 4 x 10/100/1000 Mbit/s w/ vlan support Ethernet
- Qualcomm Atheros QCA8337 switch
- 1 x 3.0 + 1 x 2.0 (combo with eSata port)
- 115200, 8N1 internal serial console
- Power, Reset, WPS and WLAN buttons
- Power, WPS and WLAN leds
- 12 VDC, 3 A power
Installation:
The installation must be done using web interface of the router.
To achive this new firmware-utils tool was added to set correct
magic headers for the factory images.
Installation from vendor firmware:
1. Flash over the native Linksys WEB interface using factory image.
Installation using recovery mode:
1. Power off the device and disconnect the WAN port.
(Only LAN port to be connected)
2. Press & hold the "Reset" button
3. Power on the device & wait 10 seconds with pressed "Reset" button
4. Set IP Internet Protocol on your PC from
192.168.1.0/24 network (Router is on IP 192.168.1.1)
5. Open the Firmware Recovery page in your browser:
http://192.168.1.1/index.shtml
Firmware Recovery -> File Name -> Recovery & Reboot
The device page in inbox:
https://openwrt.org/inbox/toh/linksys/linksys_ea8350_1
Signed-off-by: Sergey Filippov <sergey.filippov@outlook.com>
Link: https://github.com/openwrt/openwrt/pull/15798
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
All three PCIe ports are reported non working on Meraki MR42/MR52 boards
since kernel 6.1 with the issue of PCIe PHY link never coming up thus
no WLAN cards are available on the boards.
After debugging it seems that PCIe worked on 5.15 and older purely by
accident as device DTS was using /delete-property/ perst-gpios; in each
of the 3 PCIe nodes but there was no "perst-gpios" property in the SoC DTSI
as it was still using the older "perst-gpio" property so it was not getting
removed from the device DTS.
However, in kernel 6.1 commit ("ARM: dts: qcom-*: replace deprecated
perst-gpio with perst-gpios") updated all Qualcomm DTS-es to use the newer
"perst-gpios" and thus once ipq806x moved to 6.1 PCIe stopped working as
now that property was being dropped from the device DTS.
So, since the removal of PERST pins seems to have been wrong from the start
lets drop the property removal from MR42/MR52.
Fixes: #15408
Link: https://github.com/openwrt/openwrt/pull/15509
Signed-off-by: Robert Marko <robimarko@gmail.com>
There is a custom LED controller between the 3 SoC GPIO outputs and
the red and blue LEDs of the device. It implements a strange mapping
that includes fixed, flashing, and breathing modes.
The current DTS configuration causes OpenWrt to flash the LEDs over
the controller's own flashing, resulting in chaotic output in boot,
failsafe, and upgrade modes.
This change fixes the LEDs in the best way possible as long as each
OpenWrt running state is limited to be signaled by a single led.
Signed-off-by: Rodrigo Balerdi <lanchon@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/15440
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
LAN Leds on Meraki MR52 are wrong and needs to be swapped to actually
reflect real ports (lan1<->lan2).
Fixes: #15388
Signed-off-by: Mieczyslaw Nalewaj <namiltd@yahoo.com>
Link: https://github.com/openwrt/openwrt/pull/15410
[ wrap commit to 80 columns and improve commit title ]
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Since with recent kernel version DTS moved to a dedicated directory,
it's required to split files to per kernel version to follow kernel
version directory structure.
Also makes use of DEVICE_DTS_DIR to target the correct DTS directory
based on the kernel version.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
